1. What is LATAPOXY® 2000, Industrial epoxy grout?
LATAPOXY® 2000, Industrial epoxy grout is epoxy resin based joint filling materials for tile / stone joints, used in industrial floor and wall areas. This grout is a proven product over 50 years.
2. What is the pack size of LATAPOXY® 2000, Industrial epoxy grout?
The pack size available: 10 Kg.
3. Where can I use this grout?
You can use LATAPOXY® 2000, Industrial epoxy grout for internal and external (Covered) areas like commercial, Industrial floors and walls to install in the joints of ceramic / vitrified/ glass mosaic/metal tiles and engineered marble/quartz stones, natural stones etc. One can use epoxy grout in commercial kitchens, hospital laboratories, chemical laboratories besides heavy chemical industrial floors, Pharma and food industrial floors and walls.
4. How much water is to be mixed with LATAPOXY® 2000?
No water should be mixed with this product. It is a resin based pre-packed grout which has three components, namely Part A, Part B and filler powder Part C. Only these components should be mixed to make grout which is easy to apply and clean.
5. What is preparation to be done before application of LATAPOXY® 2000 grout?
The following preparation must be done before application of LATAPOXY® 2000 grout:
a) Clean the surface of the tiles and joints free of dust and debris with wet cloth or sponge. Remove spacers from the joints.
b) Find out if the tiles were washed with acid based cleaners. If washed with acid based cleaners, wash the tiles again with plenty of clean water to remove any acidic remains in the joints.
c) Don’t allow water to stand in the grout joints prior to grouting. Allow the joints to become dry.
d) Check if all the tools and sufficient grout material is available for completion of job without any disturbance.
e) Cordon off the area and don’t allow any traffic after cleaning the joints.
6. What are the precautions to be taken while applying LATAPOXY® 2000 grout?
The following precautions are very important and critical while application of LATAPOXY® 2000, epoxy grout:
a) Don’t do part mixing. The grout components are pre-packed and need to be used completely. For small areas mix liquid components (Part A and Part B) first and then add filler powder to the already mixed liquid. There are two sets of Part A, 2 sets of Part B and 2 sets of Part C in the pack of LATAPOXY® 2000.
b) Do not mix the grout in dirty pails, buckets. Always use clean pail to get the best results.
c) Use gloves while mixing and applying the epoxy grout. A pair of gloves is provided in the grout pack.
d) Don’t use putty blades for application of grout: Putty blades are metallic blades which will leave scratches on the tile surface. ALWAYS USE RUBBER FLOATS so that the tile doesn’t get scratched.
e) Don’t allow any other works like plumbing, electrical fittings, plastering, tiling or painting to be done in the grouting area while applying the epoxy grout. If there is dust in the air, it settles down on the grouted joint which will be difficult to remove. Don’t allow any traffic other than people who are working with epoxy grout.
f) Start initial cleaning with the scrubber provided in the kit in about 45 minutes time from the time of filling up of joints. If not done, it is difficult to remove the grout haze and excess grout after couple of hours. Final cleaning must be carried out after 24 hours from the time of first cleaning.
g) Do not smoke while working with the epoxy grout. Do not allow any fire producing elements to the site while working with epoxy grout.
h) Always use potable quality clean water for first and final cleaning of the grout joints.
7. When can I allow foot traffic and heavy traffic on floor joints filled with LATAPOXY® 2000?
Foot traffic is allowed after 24 hours from the final cleaning of the grout. Heavy traffic is allowed only after 7 days from the day of final cleaning of grout joints. For water bodies, it is recommended to fill the water only after 7 days from the day of final cleaning.
8. What is the minimum size and maximum size of joint that can be filled using LATAPOXY® 2000, Industrial epoxy grout?
The minimum width of joint should be 2mm and maximum size (width) of joint should be 12mm for installation with LATAPOXY® 2000. If you are installing LATAPOXY® 2000 in joints wider than 12mm ask MYK LATICRETE team member for a suitable epoxy grout.
9. Can I use LATAPOXY® 2000 for external tile joint filling?
No. One can use LATAPOXY® 2000 for covered areas only in case of exterior tile/stone joint installation. This product is not suitable for external facades and floors if they are not covered.
10. But if I have a STP (Sewage Treatment Plant in the exterior, can I use LATAPOXY® 2000?
Yes. When you want to fill tile joints of STP with LATAPOXY® 2000, you can do so by leaving one joint at every 12 ft distance in both directions. These joints can be subsequently filled using a silicone / Polysulphide sealant. For further details, seek advice from MYK LATICRETE team member.
11. What are the advantages of LATAPOXY® 2000, Industrial epoxy grout?
The biggest advantage is it is highly chemically resistant and protects the joints from chemical attack due to spillage of different acids, alkalis etc. Besides this, being a solid epoxy grout, it does not crack, powder or disintegrate with time. Please refer the chemical resistance chart for resistance to various chemicals in industries, laboratories and commercial kitchens,
12. Do I get the color that I like to match my tiles?
LATAPOXY® 2000 stain free epoxy grout is available in limited colors like colors of industrial tiles.
13. Can I do the application of LATAPOXY® 2000, Industrial epoxy myself?
Though the product is easy to use, it is always recommended to have an experienced application contractor engaged for installation of LATAPOXY® 2000 grout. Follow all the precautions specified above while applying the epoxy grout. Seek the help of MYK LATICRETE team member for application.