Image Image Image Image Image
  • LATICRETE® 111 + 4237

  • LATICRETE® 111 CRETE FILLER POWDER
    LATICRETE® 111 Crete Filler Powder is a factory prepared blend of carefully selected raw materials, portland cement and graded aggregates. Designed for use with LATICRETE® 73 Crete Admix to produce high strength adhesive for fixing all varieties of small to large format tiles and stones.

    LATICRETE® 4237 HIGH PERFORMANCE LATEX ADMIX
    LATICRETE® 4237 Latex Admix is a specially designed High Performance Latex additive for use with LATICRETE® 111 Crete Filler Powder to make high strength thin bed adhesive. It is suitable for installation of all types of ceramic tile, vitrified tile, natural stone & agglomerates. It has superior bond strength & is flexible and also highly resistant to shock & impact.

    These features make it a premium choice for installation of tile & stone in high demanding areas such as external facades, industrial floor, high traffic areas etc.

    • 111Adhesive Powder: 20 kg

      4237 Latex Admix: 20 litres

    • Approx. 55-60 sq. ft per 5 ltrs, mixed with 20 kg bag LATICRETE® 111 Crete Filler Powder / Adhesive using a ¼” x ¼” (6mm x 6mm) square notch trowel for a bed of 3 mm.

    • Grey and White (L 111)

    • • ANSI: A118.4, EN 1348 or ISO 13007 for C2TES1
      • ISI: TYPE 2 ADHESIVE
      • VOC: Nil

    • • Superior bond strength
      • Flexible and shock & impact resistant
      • Rated for extra heavy traffic conditions.
      • Proven versatility

    • Substrate:

      The surface to be covered with tile/stone shall be sound and confirm to good design, rigid, clean and free of dirt, oil, grease, curing compounds, form release agents or loose plaster and paint. For economy the surfaces should be level and true within:

      Walls – 3mm in 2.5m

      Floors – 1.5mm in 1.0m

      Note:

      1. The Gypsum wall board shall be fixed as per the manufacturer’s guidelines. Ensure the gaps between two adjoining boards are treated with a filling material or tape so that the adhesive is not allowed into the joints.

      2. Gypsum wall board is not a suitable substrate for exterior tile installation or interior areas subject to constant water exposure.

      3. The joints between two Gypsum wall boards should be continued through to the top of the tile. At no point of time, tiles should be installed directly on the joints.

      Surface Preparation:

      a) Ensure the surface of Gypsum board is clean and free from impurities like dust, dirt, debris, oil, grease, curing agents, loose              plaster etc.

      b) Dampen lightly, the surface before application of thin set adhesive

      c) Clean the back of tile/ stone for any dust or coating.

      Mixing:

      The products can be mixed by hand or slow speed electric drill mixer (less than 300 rpm).

      Pour LATICRETE® 4237 in a clean container and then add the powder LATICRETE® 111 and mix until the mixture becomes creamy and plastic. Do not over mix. Leave the mix to slake for 5-10 min and remix before use. Mix only sufficient quantity of adhesive for immediate need.

      Proportion: Approximately 1 bag of LATICRETE® 111 with 5.5 ltrs of LATICRETE® 4237. Adjust quantity of liquid to obtain proper consistency.

      Installation:

      Wet the surface and remove the excess water before applying the adhesive. Ensure the area is shaded from sunlight. The adhesive shall be applied with the flat side of the trowel using a scraping motion to work the material into good contact with the surface to be covered. Additional mortar is then applied with the notched edge of the trowel.

      When installing large tiles/ stones, spread adhesive onto back of tile in addition to trowelling material over surface to be tiled. Select proper type of notched trowel.

      a)    Thin Tiles upto size 300 X 300 mm, use a square notched trowel of size 6mm X 6mm to provide a total thickness of 3mm

      b)    Large Porcelain Tiles upto 450 X 450 mm with ribs, use a square notched trowel of size 6mm X 6mm and back butter the tile with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 4.5 mm

      c)    Large Porcelain Tiles upto 600 X 600 mm with ribs, use a square notched trowel of size 6mm X 9mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 6mm

      The most important standard to keep in mind is to insure that the piece of tile is completely bedded in the mortar or adhesive with 100% coverage.

      Rear face of tiles (especially Porcelain tiles) should be cleaned with damp sponge to clean all the dust. Do not saturate in water.

      Excess mortar on adhesive shall be cleaned from the surface of the stone with wet cloth or sponge while the mortar is fresh.

    • Designed for installation of all types of ceramic tile, Vitrified tile, brick, natural stone and agglomerates. LATICRETE® 4237 Latex admix offers the speed and economy of adhesives with the permanent, water resistant dependability of portland cement.